149-X is an all purpose liquid detergent for exterior aircraft and vehicle cleaning, as well as industrial and maintenance applications. It can be applied by foam, spray or hand application. 149-X is also an excellent all-purpose cleaner and can be used for cleaning walls, floors and even as a light-duty steam cleaning compound.
Activator is a blend of penetrants formulated to improve paint stripping of alkaline solutions. Socostrip A-0101N Socostrip A-0101N is a thickened water based emulsion paint stripper activated by hydrogen peroxide, such as epoxies and polyurethanes, and used to remove top coats from aircraft surfaces.
Compared to traditional surfactant formulations, ADISSOL offers the advantage of increasing the tolerance to the level of oils and greases in the bath, while retaining excellent performance.
Evasol rapidly cuts through grease and grime to provide fast and easy cleaning of surfaces made of glass, chrome, vinyl, tile, porcelain, or stainless steel.
HDL-330 is a medium duty liquid, multi-metal safe degreaser. It is intended for use where caustic based products and petroleum distillates, cannot be used.
Kemstrip-596 is a liquid stripper formulated to remove a wide variety of coatings such as phenolic acrylic and nitrocellulose lacquers, polyurethanes, and epoxies. These are the types of finishes commonly used on aircraft surfaces and engine components, such as impeller blades, transfer cases, diffuser cases, wheels and landing gear. Kemstrip-596 can be used as a heavy-duty decarbonizer.
MagClean 1710-A is a specially compounded acidic product used for the removal of exhaust stains, light oxides and corrosion from metal surfaces, resulting in a clean and lightly etched surface for maximum paint adhesion. It is excellent for repair or rebuilding shop use in hot or cold immersion for corrosion removal from ferrous or nonferrous metals. It is also an effective degreaser.
MagClean 2175-AP is a unique product designed to optimize your cleaning equipment. This product is formulated to wash immersion or spray washer cleaning equipment.
MagClean 2190-A is a new generation of cleaning product specially formulated to break down the bonding materials in concrete, turning hardened cement into a easily rinsable sludge. It is also effective on the cleaning of scale and lime residues, and the etching and surface preparation of concrete.
MagClean 2200-A is a new generation of cleaning product specially formulated to break down the bonding materials in concrete, turning hardened cement into an easily rinsable sludge. ScaleSafe 200 completely dissolves and releases concrete from the surface to which it is adhered. It is also effective on the cleaning of scale and lime residues, and the etching and surface preparation of concrete.
MagClean 2300-B is a new universal and powerful degreaser that is based on a new surfactant chemistry that provides very strong wettability characteristics. These new wetting agents are designed to break oil into micro-particles that are easily removed. The CANADIAN FOOD INSPECTION AGENCY has approved MagClean 2300-B as a hard surface cleaner to be used in food processing industries.
MagClean 2340-B is an all purpose liquid detergent formulated to clean various types of soils from industrial equipment. It can be applied by foam, spray or manually. MagClean 2340-B is highly effective as a general-purpose maintenance cleaner.
MagClean 2400-B is a ecological, multi-purpose, alkaline product designed specifically for industrial cleaning. MagClean 2400-B will dissolve grease and oil as well as an accumulation of other soils such as carbon residue. It can be applied manually with a brush or with a foaming unit on surfaces such as floors, walls, parts or vehicles.
MagClean 2410-B is a heavy duty liquid d-limonene based multi-metal safe degreaser. MagClean 2410-B is intended for use where caustic based products, petroleum distillates and oil emulsions cannot be used.
MagClean 2420-B is an all purpose liquid detergent formulated to clean various types of soils. It can be applied by foam, spray or hand application. This colloidal detergent can also be used for cleaning walls, floors, and as a steam cleaning compound. Detersol is excellent for removing atmospheric contamination from RV's and exterior siding.
MagClean 2480-B is unsurpassed for general cleaning of industrial equipment and machinery. It is also highly recommended for heavy-duty cleaning of exhaust track and rocket blast areas of painted or unpainted aircraft surfaces in addition to general exterior aircraft cleaning. MagClean 2480-B can be used with foam generating equipment or applied by spray, mop, brush or sponge.
MagClean 2520-N is a high performance, ecological degreaser that efficiently dissolves asphalt and tar. MagClean 2520-N does not contain any petroleum based raw materials. This product was specifically designed to clean industrial equipment including heavy equipment used in the application and transport of asphalt and all the associated tools.
MagClean 2750-B is a heavy duty, liquid alkaline detergent for cleaning oil, grease, and other soils from equipment, through a Magnus Foam & Clean dispenser, steam cleaner or high pressure washer.
MagClean 3320-B is a liquid spray wash compound designed as a superior quality, low pH product for the removal of soils, including sulfurized, chlorinated or other types of metalworking lubricants in applications as low as 26.6°C (80.0°F).
MagClean 3350-B is a light to medium duty, non-phosphated alkaline spray wash liquid. It is designed for general cleaning applications and is multi-metal safe.
MagClean 3400-B is a non phosphated, high strength alkaline spray-washing liquid compound. It is intended for use in multi-metal cleaning applications.
MagClean 3400-BP is a specially formulated, multi-metal safe, spray wash compound for the removal of oils, marking inks, drawing lubricants and other soils from most metals.
MagClean 3450-BP is a specially formulated, multi-metal safe, spray wash or immersion cleaner for the removal of oils, hydraulic fluids, and other soils from all metals. It is an efficient cleaner for aircraft wheels and brake assemblies.
MagClean 3880-BP is a highly alkaline powdered spray wash compound. MagClean 3880-BP is excellent for removing carbon, pitch, paint, heavy grease and light rust from all types of ferrous parts.
MagClean 4320-B is a liquid concentrate developed to prevent rusting of steel and other ferrous parts. It is used as an inhibitor for steel media to prevent rusting during prolonged storage or shutdown exceeding 24 hours. MagClean 4320-B contains no nitrites.
MagClean 4340-B is a concentrated liquid compound, especially formulated to do effective cleaning of oils, to aid deburring and burnishing and to be used in all cleaning applications.
MagClean 4360-B is a corrosion inhibitor developed to give medium term corrosion protection on sintered and cast iron parts. MagClean 4360-B provides excellent corrosion protection with good cleaning, low foam and good burnish. It is used on all metals except zinc.
MagClean 4400-A has been especially formulated as a mildly acidic burnishing compound to produce lustrous surfaces on zinc, steel, brass, aluminium, stainless steel, copper and its alloys.
MagClean 4420-A has been especially formulated as a mildly acidic burnishing compound to produce lustrous surfaces on zinc, steel, copper, brass, aluminium and stainless steel.
MagClean 4430-B was designed to be used as a deburring compound on all non-ferrous metals to provide clean, light coloured surfaces. It is used effectively with ceramic, resin-bonded, natural stones, and fused aluminium oxide media. It can defoam resin-bonded media.
MagClean 4460-A is a liquid compound that is recommended when steel media is used. Excellent burnishing and bleaching, produces bright steel, copper, brass and aluminium parts.
MagClean 4470-A has been specially formulated as a mildly acidic burnishing compound to produce lustrous surfaces on zinc, steel, brass, aluminium, stainless steel, copper and its alloys.
MagClean 4480-A is a liquid compound that is recommended when steel or stainless steel media is used. Excellent burnishing and bleaching, produces bright steel, copper, brass and aluminium parts.
MagCool 5500 is a new fully synthetic machining fluid, designed for difficult operations and also high pressure applications because it is non foaming.
Magnuspray 204 is designed to remove shop soil and oils, light water scale, some paints and resinous deposits from a variety of surfaces including plastic or steel, in low or high temperature applications.
Socostrip A-0101N is a thickened water based emulsion paint stripper activated by hydrogen peroxide, such as epoxies and polyurethanes, and used to remove top coats from aircraft surfaces.
Soluwax is a blend of surfactants and penetrants used as an immersion cleaner. It is used as part of an aqueous wax dissolving process or an aqueous degreasing process that replaces vapour degreasing and the use of chlorinated solvents.
CAL1600 is a lubricant recommended for use at 100% in applications like, but not limited to, sawing of Aluminum using a band or a circular saw. CAL1600 may also be used in more demanding applications as experienced with harder materials such as steel.
CAL 2230-W is a water-soluble lubricant intended to be used in the manufacturing process of vibro-compacted carbon anodes used in electrolysis operation of light metals.
CAL®64 is recommended to be used as is, to draw bright MIG & TIG wire from alloys such as 5056, 5356, 4043. It is also useful in press drawing applications for aluminum parts. CAL®64 is used for light forming of brass and can be recycled by a centrifuge system. This lubricant can also be used for ferrous wire drawing applications.
CAL®76 is recommended to draw wire of various alloys such as 1350, 6101, 6061. The product is a mineral oil based lubricant, which is not water emulsifiable. It is used straight/undiluted.
CAL®92 is a new generation, fully biodegradable fluid, used as a lubricant in metal forming operations, such as vertical or horizontal continuous casting of aluminum and magnesium.
CAL®950 is a fully synthetic fluid used as a lubricant in severe metalworking operations such as cutting and sawing. It is formulated for application by a non atomizing misting device.
CAL®96 is a friction reducing fluid formulated for use in non-ferrous (aluminum, magnesium, cuprous alloys) metal cutting operations. It should be applied through a metered misting device, to the cutting edge of the tool directly, in front of the cut.
CAL®97 is a synthetic fluid used as a lubricant in cutting 3xxx aluminum series. The cutting is applied by an appropriate misting device that will not atomize the fluid.
CAL®98 is a fully synthetic fluid used as a lubricant in severe metalworking operations on aluminum, magnesium and copper alloys, such as cutting, sawing, stamping, etc. It should be applied by an appropriate misting device that will not atomize the fluid.
CAL®99 is a synthetic fluid used as a lubricant for non ferrous materials in severe metalworking operations such as cutting, sawing, stamping, and special press-drawing operations.
Cal® 999 is a low viscosity synthetic based fluid used as a lubricant. It is intended to be applied by an appropriate misting device that will not atomize the fluid. Cal® 999 is used in non-ferrous metal working operations such as cutting, sawing, stamping, and other specialized operations. It is ideal for sawing of aluminum or magnesium, ingots and T-ingots.
MagFix 4010 is a liquid product that is used to decrease chemically high hardness waters. It is used in conjunction with metalworking fluids such as emulsifiable coolants, semi-synthetic coolants and synthetic fluids.
MagFix 4060 is a liquid that will contribute to increase the hardness of a soft water. This product is normally used in conjunction with emulsifiable coolants, micro-emulsifiable coolants and/or synthetic fluids.
Magnicide MW is an anti-microbial additive capable of controlling most bacterial problems normally encountered when using aqueous fluids in metalworking operations.
Magnu-Draw 40 is an inhibited and chlorinated oil designed for deep drawing, blanking and stamping. It is formulated to eliminate the corrosion normally associated with deep drawing chlorinated oils.
Magnu-Draw 50L combines low viscosity and maximum chlorine content with advanced inhibitors and emulsifiers to provide maximum versatility in an oil for extremely severe draws. The low viscosity reduces tackiness between parts and the die. Magnu-Draw 50L will perform a wide range of tasks.
MagSlip 1110 is a pale sparkling clear, paraffinic oil for use in all types of EDM machines. Its low viscosity assures good filterability, rapid settling, good penetration and heat transfer. It is non staining and has a low odor.
MagSlip 1320 is a new generation fully biodegradable fluid. MagSlip 1320 is used as a lubricant in high temperature metal transforming operations, such as cutting, sawing, stamping, and special press drawing operations. MagSlip 1320 can also be used with wood and plastic.
MagSlip 1330 is a friction reducing fluid formulated for use in nonferrous metal cutting operations. It is meant to be applied through a metered misting device, to the cutting edge of the tool directly in front of the cut.
MagSlip 1340 is a fully synthetic fluid used as a lubricant in severe metalworking operations such as cutting, sawing, stamping, and special press-drawing operations. It is meant to be applied by an appropriate misting device that will not atomize the fluid.
MagSlip 1510 is a low viscosity oil fortified with a high concentration of EP additives to provide significant increases in honing production rates, while extending stone life dramatically.
MagSlip 1590-C is a heavy-duty lubricant for difficult machining operations such as gun drilling and broaching. The high content of chlorine, sulphur and fat ensures maximum tool life and surface finish.
MagSlip 1650-C is an oil with exceptionally high chlorine, sulphur and fat content. The product is low in viscosity, which enables it to settle fines rapidly. Because of its low viscosity, the product can be recycled easily. Mag-Lub®333 is also excellent for gun drilling and honing applications, and can be used as an additive to increase performance of neat oils not containing sufficient E.P. additives.
MagSlip 2100-E is lubricating oil recommended for blanking, forming and light duty stamping of aluminium galvanized steel, tin coated steel, copper, brass and pre-painted steel. MagSlip 2100-E is also an excellent glass-cutting lubricant widely used in the glass industry and in window manufacturing.
MagSlip 2200-E is lubricating oil recommended for blanking, forming and light duty stamping of aluminium, galvanized steel, tin coated steel, copper, brass and pre-painted steel. MagSlip 2200-E has almost no odour, making it an ideal choice for applications in close proximity to operators.
MagSlip 2205-E is lubricating oil recommended for blanking, forming and light duty stamping of aluminium, galvanized steel, tin coated steel, copper, brass and pre-painted steel. Also used for roll forming of light gauge metals including stainless steel. The product has almost no odour, making it an ideal choice for applications in close proximity to operators or in closed areas with limited ventilation.
MagSlip 2210-E is lubricating oil recommended for blanking, forming and light duty stamping of aluminium, galvanized steel, tin coated steel, copper, brass and pre-painted steel. MagSlip 2210-E has almost no odour, making it an ideal choice for applications in close proximity to operators.
MagSlip 2215-E is an E.P. fortified forming lubricant that is recommended for fine blanking, forming and stamping on aluminium, galvanized, pre-painted sheet stock, tin coated sheet, copper and brass.
MagSlip 2520-W is a new water soluble lubricant for stamping carbon steels, aluminum, copper and brass. It is formulated to provide superior performance compared to conventional water extended products such as soluble oils and soap-fat pastes.
MagSlip 2540-W is a water soluble metal sheet stamping lubricant that provides hydrodynamic boundary slip and extreme pressure lubrication. MagSlip 2540-W is water soluble and can be used at different concentrations in relation to the severity of the process. MagSlip 2540-W is an excellent choice for the replacement of mineral oil based stamping fluids.
MagSlip 2610 is an economical deep drawing lubricant, primarily for steel. It is used in severe drawing applications such as oil pans. This lubricant can replace paste-type product and its user friendly.
MagSlip 2650 is a liquid stamping and drawing compound. This product has been formulated to provide excellent rust protection for formed parts, as well as for the press. The product contains emulsifiers which make it very easy to clean after processing.
MagSlip 2710-C is a chlorinated drawing and stamping oil designed to increase die life. The product is very versatile, and can be used over a broad concentration range to perform a wide variety of tasks.
MagSlip 2720-C is a viscous inhibited chlorinated oil designed for deep drawing, blanking and stamping. It has both hydrodynamic and EP properties for excellent performance in many heavy duty applications.
MagSlip 2730-C is a dark amber, inhibited, chlorinated lubricant. MagSlip 2730-C is very versatile, and can replace almost all other stamping and drawing lubes in a shop, enabling companies to have one vendor for all their needs.
MagSlip 2740-C is a inhibited chlorinated oil designed for deep drawing, blanking and stamping. It is formulated to eliminate the corrosion normally associated with deep drawing chlorinated oils.
MagSlip 2750-C combines low viscosity and maximum chlorine content with advanced inhibitors and emulsifiers to provide maximum versatility in an oil for extremely severe draws. The low viscosity reduces tackiness between parts and the die. MagSlip 2750-C will perform a wide range of tasks.
MagSlip 2850-P is a, high film strength, fortified drawing oil for ferrous rod and wire. It is recommended in operations where the use of sulphur and chlorine is not desired. The MagSlip 2850-P viscosity is optimized to ensure surface quality, die life and cooling properties.
MagSlip 2850-PC is an economical deep drawing lubricant for steel. It is recommended in operations where the use of oil will liberate smoke. MagSlip 2850-PC provides short term inhibition against rust. MagSlip 2850-PC is ideally suited for severe draws such as oil pans.
The Diestone DLS solvent has been specifically designed as a high flash point and low VOC replacement for MEK, MPK, Acetone and Toluene. Diestone DLS is a solvent composition with controlled volatility and weak odour. It is free from chlorinated hydrocarbons and used as a cleaning agent. The product provides maximum security: it does not contain the teratogenic or carcinogenic components toluene or ethylene glycol ethers.
The Diestone HFP solvent has been specifically designed as a high flash point and low VOC replacement for MEK, MPK, Acetone and Toluene. Diestone HFP is a solvent composition with controlled volatility and weak odour. It is free from chlorinated hydrocarbons and is used as a cleaning agent. The product provides maximum security: it does not contain any teratogenic or carcinogenic components, toluene or ethylene glycol ethers.
The Diestone M-SK solvent has been specifically designed as a high flash point and low VOC replacement for MEK, MPK, Acetone and Toluene. Diestone M-SK is a solvent intended for use by spray, aerosol, wipe-on/wipe-off or immersion, to remove oil, grease, and protective films from bare or painted surfaces.
MagSolv 1250 is a multi-use polar solvent. It can be used in immersion applications or it can be applied manually to remove soldering flux residue, ink or waxes. It can also be used to replace acetone in some industrial cleaning applications.
MagSolv 1800-C is a heavy-duty solvent used for cleaning electric motors, electrical equipment and components, as well as for degreasing of metal parts.
MagSolv 1960-B is a high performance solvent for precision cleaning. It is used in many applications including vapour degreasing, ultrasonic cleaning, wipes, spraying or immersion. Xonox eliminates oils, grease, fingerprints and protective films.
MagCool 1200-C is a water emulsifiable cutting fluid, specially formulated for metalworking operations involving high temperatures. In high speed drilling, sawing, cutting, and stamping of sharp form parts or in other operations, the use of MagCool 1200-C helps to increase the quality of the surface finish and also extends tool life.
MagCool 1500-C is mineral based oil that is formulated with very high boundary and extreme heat and pressure additives. This combination contributes to a state of the art lubricant. In addition, the formulation of MagCool 1500-C does not allow bacterial growth and contributes to a long sump life.
MagCool 2350 is a new soluble oil cutting fluid for light duty applications.The use of this product immediately provides lubricity and cooling. These two benefits provide excellent surface finish on machined parts and increases tool life.
MagCool 2370 is a new generation multi purpose metalworking fluid. It contains specially selected additives (non chlorinated) so it can be used in most applications.
MagCool 2390 is a new generation soluble oil cutting fluid. This chlorine-free formula uses a new technology that allows its application on severe operations, such as extreme pressure for though alloy treatment. Its tramp oil repelling characteristics provides a supply of clean coolant to the chip/tool interface, minimizing residual films and maintaining the machine tool dirt-free.
MagCool 3300 is a micro-emulsion (semi-synthetic) cutting fluid formulated to assist in metalworking operations. The use of MagCool 3300 immediately provides lubricity and cooling.
MagCool 3400 is a micro-emulsifiable cutting fluid formulated to assist in metalworking operations. The use of MagCool 3400 immediately provides lubricity and cooling.
MagCool 5250 is a light blue synthetic grinding and machining fluid which will appeal to small shops using carbide tooling. MagCool 5250 will resist degradation and can be maintained with minimal equipment.
MagCool 5350 uses a new macro-molecular stacking mechanism which lubricates and protects steel and other metals from corrosion. This unique concept uses a film forming mechanism with selected alkanolamines and polycarboxylic salts. MagCool 5350 also uses the lubrication properties of poly alkylene glycol without their sticky deposits. This product is one of the most technically advanced lubricants in the synthetic series of coolants.
MagCool 5400 is a blend of rust inhibitors, lubricity additives, detergents, emulsifiers, and non-phenolic inhibitors to prevent degradation of the product.
MagCool 5500 is a new fully synthetic machining fluid, designed for difficult operations and also high pressure applications because it is non foaming.
MagCool 5550 is a heavy-duty fully synthetic machining fluid, which can also be used in light stamping and forming operations. It provides a higher degree of lubricity than most other synthetics.
MagCool 5600 is the state-of-the-art full synthetic lubricant for metalworking operations. It is designed to assist light to medium duty metalworking cutting operations with a variety of different metals. MagCool 5600 is the preferred choice where galvanic corrosion is induced by the intimate contact of two different metals. When used in conjunction with pure water (D.I., R.O, or others), MagCool 5600 provides a superior level of anti-corrosion properties. In addition, the formulation of MagCool 5600 does not allow bacteria growth and contributes to a long sump life.
MagFix 1010 is a liquid additive specifically designed to help control and maintain the pH of machining soluble oil coolant sumps in the 9.0 to 9.5 range.
MagSlip 2810-P is a special blend of saturated and unsaturated fats in a water based matrix. This formulation is especially designed for the lubrication of pH sensitive metals.
Corrotek is a liquid, in-process, rust preventive for use on steel parts. It provides rust protection and normally does not have to be removed prior to assembly of the protected parts.
Wadis 24 is a product that displaces water and humidity by adding a thin translucent soft film with good anti-corrosive properties and therefore giving treated surfaces water-repellency. Wadis 24 is also a releasing and lubricating agent.
